LTO5 tape is showing incorrect capacity
Hi There, I'm new to this forum, I use Backup Exec 2010 with an IBM LTO5 tape drive and we have three tapes that are showing a capacity of 35.4gb. If I try to use them it does indeed become full after 35.4gb. I've tried a full erase and everything I can think of and they're stuck at this capacity. I know it's only 3 tapes, not the end of the world... But I'm really curious as to what has happened to them. They weren't new, I think they came with the drive and had been opened. Any insight greatly appreciated!979Views0likes6CommentsSSR 2013 - ReFS support, when?
When is SSR 2013 Server Edition going to support volumes formatted as ReFS for full/incremental recovery points? BTW the discussion creation form doesn't include "Windows Server 2012" in the dropdown list of Operating systems, only Server 2003 and 2008 is there.478Views0likes4CommentsThe job failed with the following error
We have updated BackupExec from 2012 to 2014 and all job are running fine but on a few backup jobs i am receiving following error. In one job i am receiving following error.. Completed status: Failed Final error: 0xe000942a - Backup Exec did not find any resources to include in the backup. Check the backup selections for this job to make sure it includes resources that are available for backup. Final error category: System Errors For additional information regarding this error refer to link V-79-57344-37930 and another job is failing with following error: Completed status: Failed Final error: 0x2000fe07 - FS_NO_MORE Final error category: For additional information regarding this error refer to link V-79-8192-65031 Please help me out in this...Solved5.4KViews3likes3CommentsNetbackup Deduplication Engine takes lot of time to load into memory
Hello, I just wanted to know why Netbackup Deduplication Service(spoold) takes time to load into memory.(To start completely) I have seen sometimes it took more than 4 hours to start, when checking in Windows Task Manager the memory for spoold.exe is increasing gradually. Thanks & Regards Sujit2.5KViews2likes8CommentsFirewall woes: Definitive TCP Port list for Netbackup
Hi, I keep running into problems connecting to clients/servers that have firewalls running. Does anyone have a COMPLETE portlist of TCP/UDP ports that should be open, so that I can do ALL possible Netbackup actions imaginable? We are using Netbackup 6.5.6 and 7.1 in a full Windows environment. I would like to put a generic firewall ruleset that is the sameon all clients, so that Netbackup will never everbe bothered by the firewalls again... Hope someone has this information available! Thanks! FredSolved576Views0likes3CommentsBackup Exec 2010 Error "There is not enough disk space"
Hello I am running Backup Exec 2010 R3 on Windows Server 2003 R2. For the past 2 weeks, I've hadthe followingrepeated failure message on some backup jobs: Storage device "Windows Full" reported an error on a request to write data to media. Error reported: There is not enough space on the disk. V-79-57344-34034 - An attempt to write data past the end of the media has failed. This and a few other backup jobs are backing up to a 1 TB local disk on the same server on which Backup Exec is running. These backup jobs have been running successfully for the last few years but now lately the backup disk is becoming full and some jobs are failing. No configuration changes have been made. I do see that backups from a 3 or 4 days ago are still present. By deleting them, the jobs continue. I must add that all of these backup jobs were created about 4 years ago by my predecessor and I have newly taken over these responsibilities.Backup Exec is very new to me and I have a few questions: 1. I would assume that the backup jobs where the data is written to harddiskare configured such that older backed files are purged automatically: is this correct? How do I determine this in the backup job's setup? 2. I have checked the Job Setup for each of the different backup jobs and I cannot see anything which indicates that a particular backup job is backing up to a hard disk instead of to a tape. How do I determine whether data is being backed up to hard disk or to tape? 3. I think that Catalogs are part of the backup process to hard disk process. I see that there are files in the ...\Program Files\Symantec\Backup Exec\Catalogs\BackUpServer folder dating back to 2009. Are these old files necessary? I would think that Backup Exec would automatically purge old unnecessary catalog files: is this correct, or do they need tobe purged manually? Or should theynot be purged at all? Thank you for your help. Yes, I know I need to read the user guide but it's over 1200 pages long and I need to get this issue resolved before I focus on training. Best regards, SuzanSolved1.8KViews1like4Comments